VINTAGE AIR FORD 272-312" INCH Y-BLOCK COMPRESSOR & ALTERNATOR BRACKET KIT
VINTAGE AIR FORD 272-312" INCH Y-BLOCK COMPRESSOR & ALTERNATOR BRACKET KIT
*NEW*
This requires a 3-groove crankshaft pulley or a 2-groove add-on pulley 730004.
A simple & economical solution to get your Ford-powered classic air conditioned with ease. Mount compressor alternator and power steering on some applications with steel plate brackets.
We endeavour to keep stock levels as accurate as possible. However, due to the fact we sell both online and in-store, there may be slight inconsistencies in these stock levels. To confirm stock levels, please get in touch
Ford Y Block
Compressor/Alternator Bracket Kit 131111
Fits: Passenger Cars and
*See Page 2 for Additional Requirements and Recommendations
18865 Goll St. San Antonio, TX 78266 ph:
901288 REV B 04/06/16 INSTRUCTIONS, BRACKET KIT 131111, PG 1 OF 10
Bracket Systems
TM
Table of Contents
1.Cover
2.Table of Contents
3.Packing List/Parts Disclaimer
4.Accessory Mounting Holes
5.Compressor Assembly Bracket Installation
6.Alternator Mounting Bracket Installation
7.Alternator Installation
8.Compressor Installation
9.Belt Routing & Compressor Warnings
10.Packing List
Additional Info: Please Read Before Beginning
Alternator Requirements:
This bracket kit is designed for use with GM 10SI and 12SI alternators only. The following 12SI alternators are available from Vintage Air:
Additional Recommended Components:
•OEM
•
•
NOTE: This kit is designed for use with these recommended components. However, OEM
2
901288 REV B 04/06/16 INSTRUCTIONS, BRACKET KIT 131111, PG 2 OF 10
|
|
|
- |
|
|
|
Bracket Systems |
Packing List: Ford Y Block |
|
|
|
|
TM |
|
|
|
Compressor/Alternator Bracket Kit (131111) |
||
No. |
Qty. |
Part No. |
Description |
|
1. |
1 |
137010 |
Ford Y Block Compressor Assembly Bracket |
|
2. |
1 |
136030 |
Ford Y Block Alternator Mounting Bracket |
|
3. |
1 |
191035 |
Ford Y Block Compressor/Alternator Hardware Kit |
**Before beginning installation, open all packages and check contents of shipment. Please report any shortages directly to Vintage Air within 15 days. After 15 days, Vintage Air will not be responsible for missing or damaged items.
1 |
2 |
3
3
901288 REV B 04/06/16 INSTRUCTIONS, BRACKET KIT 131111, PG 3 OF 10
Bracket Systems
TM
NOTE: Before tightening bolts, assemble all brackets loosely to engine. This will ensure proper alignment of all brackets.
Accessory Mounting Holes
1.As shown below, locate accessory mounting holes both on water pump housing and on OEM generator mount on passenger side of cylinder head.
Cylinder Head |
|
Passenger Side |
Accessory Mounting |
OEM Generator |
Holes |
Mount |
|
4
901288 REV B 04/06/16 INSTRUCTIONS, BRACKET KIT 131111, PG 4 OF 10
Bracket Systems
TM
Compressor Assembly Bracket Installation
1.Using the illustration below, determine which configuration is being used, and install compressor assembly bracket with appropriate steel spacers. NOTE: There may be configurations not listed below that would require the use of customized spacers. Use spacers to achieve nominal value of 3 ” as shown in side view of water pump housing, below.
2.Install
|
Without |
|
|
Front Engine Mounting Plate |
|
Water Pump Housing |
||
With 3 ” Boss Height |
||
|
.800 L |
|
|
Steel Spacer |
|
Water Pump |
3 ” Boss |
|
Housing |
||
Height |
||
|
With Front Engine |
|
|
Mounting Plate |
|
|
.590 L |
|
|
Steel Spacer |
|
Front Engine Mounting |
||
|
Plate |
|
|
Compressor Assembly |
|
|
Bracket |
|
Front |
||
Hex Bolt |
||
Engine Mounting |
||
|
||
Plate |
|
|
|
2.535 L |
|
3 ” |
Steel Spacer |
|
2.535 L |
||
|
Steel Spacer |
|
|
.800 L |
|
9/16” Boss |
Steel Spacer |
|
Height |
|
|
Side View of |
Without Front Engine |
|
Water Pump Housing |
||
Mounting Plate |
||
With 3 ” Boss Length |
||
.590 L |
||
|
||
Water Pump Housing |
Steel Spacer |
|
|
||
With 9/16” Boss Height |
|
|
2.535 L |
|
|
Steel Spacer |
Front Engine |
|
|
|
5 |
With Front Engine |
Mounting |
Mounting Plate |
Plate |
|
|
901288 REV B 04/06/16 INSTRUCTIONS, BRACKET KIT 131111, PG 5 OF 10
Bracket Systems
TM
Alternator Mounting Bracket Installation
1.Install 1.750 length steel spacer behind compressor assembly bracket, and place .500” length steel spacer in front of compressor assembly bracket. Install alternator mounting bracket with 5 ½” hex bolt as shown below.
2.Place .500” steel spacer behind alternator mounting bracket and in front of compressor assembly bracket. Secure with 1 ½” hex bolt and 3/8” locknut as shown below.
1.750 L |
|
Steel Spacer |
|
3/8” |
|
Locknut |
|
|
Alternator Mounting |
|
Bracket |
(2) .500” |
|
Steel Spacers |
|
|
|
|
Hex Bolt |
|
|
|
Hex Bolt |
Compressor Assembly
Bracket
6
901288 REV B 04/06/16 INSTRUCTIONS, BRACKET KIT 131111, PG 6 OF 10
Bracket Systems
TM
Alternator Installation
1.Place .500 length steel spacer on water pump housing mounting hole as shown below.
2.Insert alternator behind alternator mounting bracket and secure with
NOTE:
3.Install
Water Pump
Housing
.500 L
Steel Spacer
5/16” |
||
Flat Washer |
||
Hex Bolt |
||
|
Alternator
Alternator Mounting |
½” |
||
Bracket |
|||
Hex Bolt |
|
||
|
|
7
901288 REV B 04/06/16 INSTRUCTIONS, BRACKET KIT 131111, PG 7 OF 10
Bracket Systems
TM
Compressor Installation
1.Install a
2.Install compressor onto compressor assembly bracket, and secure with (2)
3.Install a
Passenger Side
OEM Generator
Mount
7/16”
Flat Washer
Hex Bolt
Compressor
Assembly
Bracket
Compressor
3/8”
Locknut
3/8” |
|
Flat Washer |
|
|
Hex Bolt |
|
|
|
Hex Bolt |
|
3/8” |
|
Locknut |
|
3/8” |
|
Locknut |
|
Compressor |
|
Passenger Side |
|
View |
Hex Bolt
Compressor
Assembly
Bracket 8
901288 REV B 04/06/16 INSTRUCTIONS, BRACKET KIT 131111, PG 8 OF 10
Bracket Systems
TM
Belt Routing
1.Route belts as shown below. Vintage Air recommends using only Dayco, Gates or Goodyear brand reinforced
|
|
Crankshaft Pulley |
|
|
|
|
|
(Available from Vintage Air) |
|
||
|
Water Pump |
730004 |
1 2 |
Balancer |
|
Alternator |
Pulley |
|
|
|
|
|
Front |
|
|
||
|
|
|
|
||
|
Crankshaft Pulley Grooves: |
|
|
||
|
1. Not Applicable/Power Steering |
|
|||
|
2. Crankshaft and Compressor |
|
|
||
Front Groove of |
|
|
|||
1. Balancer, Alternator and Water Pump Pulley |
|||||
Compressor Pulley |
|||||
|
|
|
|
||
|
Rear Groove |
|
|
|
|
|
of |
|
|
|
|
|
Crankshaft Pulley |
|
|
|
Compressor Warnings
NOTE: Failure to follow these procedures will void all warranties.
1.With compressor kit installed and belt tightened, check angle of oil plug on compressor. As shown below, oil plug must not exceed 90° beyond vertical centerline.
2.Do not connect compressor clutch wire until system is being charged with refrigerant. Running compressor without refrigerant charge will result in compressor failure.
Centerline
Oil Plug
90°
90°
|
Suction |
Discharge |
|
|
|
Compressors Are |
Rear View |
|
Factory Charged |
|
|
of Compressor |
|
|
with Oil |
|
|
Installed on Bracket |
|
|
|
|
IMPORTANT NOTICE:
Do not connect compressor clutch wire until system is being charged with refrigerant. Running compressor without refrigerant will destroy compressor and void warranty.
9
901288 REV B 04/06/16 INSTRUCTIONS, BRACKET KIT 131111, PG 9 OF 10
|
|
|
- |
Packing List: Ford Y Block |
||
|
|
Bracket Systems |
||||
|
|
|
|
|
||
|
|
|
TM |
|
|
|
|
|
Compressor/Alternator Bracket Kit (131111) |
||||
No. |
Qty. |
Part No. |
Description |
|
|
|
1. |
1 |
137010 |
Ford Y Block Compressor Assembly Bracket |
|
|
|
2. |
1 |
136030 |
Ford Y Block Alternator Mounting Bracket |
|
|
|
3. |
1 |
191035 |
Ford Y Block Compressor/Alternator Hardware Kit |
|
|
Checked By:
Packed By:
Date:
1 |
2 |
3
901288 REV B 04/06/16 INSTRUCTIONS, BRACKET KIT 131111, PG 10 OF 10
The information below is required for social login
Sign In
Create New Account