1970-78 MOPAR 318/340/360 COMPRESSOR/ALTERNATOR BRACKET KIT WITH POWER STEERING (NO AIR PUMP)
1970-78 Mopar 318/340/360 Compressor/Alternator Bracket Kit With Power Steering (No Air Pump)
We endeavour to keep stock levels as accurate as possible. However, due to the fact we sell both online and in-store, there may be slight inconsistencies in these stock levels. To confirm stock levels, please get in touch
Compressor/Alternator Bracket Kit with Power Steering, without Air Pump
18865 Goll St. San Antonio, TX 78266
Phone:
Sales: sales@vintageair.com
Tech Support: tech@vintageair.com
www.vintageair.com
Bracket Systems
TM
www.vintageair.com
Table of Contents
Cover.................................................................................................................................. |
1 |
Table of Contents................................................................................................................. |
2 |
Packing List/Parts Disclaimer.................................................................................................. |
3 |
Engine Disassembly.............................................................................................................. |
4 |
Heater Fitting Replacement................................................................................................... |
5 |
Compressor Bracket Installation............................................................................................. |
6 |
Compressor/Alternator Installation......................................................................................... |
7 |
Belt Routing, Compressor Warning......................................................................................... |
8 |
Packing List......................................................................................................................... |
9 |
2 |
Bracket Systems
TM
www.vintageair.com
Packing List:
Compressor/Alternator
Bracket Kit
No. |
Qty. |
Part No. |
Description |
1. |
1 |
166018 |
Bracket, Compressor/Alternator |
2. |
1 |
Bracket, Alternator Adjuster |
|
3. |
1 |
Hardware Kit |
**Before beginning installation, open all packages and check contents of shipment. Please report any shortages directly to Vintage Air within 15 days. After 15 days, Vintage Air will not be responsible for missing or damaged items.
1 |
2 |
3
NOTE: Images may not depict actual parts and quantities.
Refer to packing list for actual parts and quantities.
3 |
Bracket Systems
TM
www.vintageair.com
Engine Disassembly
1.Disconnect battery
2.Drain coolant.
3.Remove belts.
4.Remove stock compressor and alternator.
5.Remove (3) water pump bolts as shown in Figure 1, below.
Remove (3) Water Pump Bolts
Figure 1
4 |
NOTE: Before tightening bolts, assemble all brackets loosely to engine. This will ensure proper alignment of all brackets.
Bracket Systems
TM
www.vintageair.com
Heater Fitting Replacement
1.On both
2.On
Intake
OEM |
45° 3/8” NPT to |
OEM |
Photo 1 |
Heater Fitting |
5/8” Barb Fitting |
Intake Plug |
|
Intake
|
Photo 2 |
|
|
5 |
|
|
|
Bracket Systems
TM
www.vintageair.com
Compressor Bracket Installation
1.Install the compressor/alternator bracket using (2) .500” length spacers, (2)
(2)
(2) .500” Length Spacers
Figure 2
Compressor/Alternator
Bracket 166018
(2)
Hex Bolts(2)
6 |
Bracket Systems
TM
www.vintageair.com
Compressor/Alternator Installation
1.Install the compressor onto the compressor/alternator bracket using (3)
2.Install the alternator onto the compressor/alternator bracket using (2)
3.Install the alternator adjuster bracket onto the compressor/alternator bracket using a
(See Figure 3, below).
4.Insert a .250” length spacer between the alternator and the alternator adjuster bracket. Secure the bracket to the alternator using a
If pulleys are needed, the following are available from Vintage Air:
735006 —
735007 —
|
(2) |
|
|
Locknuts |
|
|
Locknut |
|
|
|
|
(2) |
|
|
Hex Bolts |
|
Right Side |
|
|
|
|
|
View |
|
|
(3) |
(2) |
|
Hex Bolts |
Locknuts |
|
|
Figure 3
.250” Length
Spacer
Alternator
Adjuster Bracket
Flat Washer
Water Pump Pulley
(OEM Mopar # 3462825 or Vintage Air Part # 735006)
Hex Bolts
Crankshaft Pulley
(OEM Mopar # 3614377 or
Vintage Air Part # 735007)
Hex Bolt
7 |
Bracket Systems
TM
www.vintageair.com
Belt Routing
1.Route belts as shown below, and tighten the alternator and alternator adjuster bracket. Vintage Air recommends using only Dayco, Gates or Goodyear brand reinforced
Compressor belt length of 55” inches is recommended. Power steering belt length of 37” is recommended.
Compressor
Water Pump
Alternator
Power Steering
Crankshaft
Compressor Warnings
NOTE: Failure to follow these procedures will void all warranties.
1.With compressor kit installed, and belt tightened, check angle of oil plug on compressor. As shown below, oil plug must not exceed 90˚beyond vertical centerline.
2.Do not connect compressor clutch wire until system is being charged with refrigerant. Running compressor without refrigerant charge may result in compressor failure.
IMPORTANT NOTICE:
●Do not connect compressor clutch wire until system is being charged with refrigerant. Since an A/C system relies on refrigerant to circulate lubricant, running the compressor without refrigerant may
destroy the compressor and void the warranty.
● Proper compressor orientation is important. Sanden compressors may be rotated |
90˚ |
90˚ |
|
from vertical (oil fill plug at top) up to 90˚ in either direction (See illustration). |
|||
|
|
8 |
Bracket Systems
TM
www.vintageair.com
Packing List:
Compressor/Alternator
Bracket Kit
No. |
Qty. |
Part No. |
Description |
||
1. |
1 |
166018 |
Bracket, Compressor/Alternator |
||
2. |
1 |
Bracket, Alternator Adjuster |
|
|
|
3. |
1 |
Hardware Kit |
|
|
Checked By:
Packed By:
Date:
1 |
2 |
3
NOTE: Images may not depict actual parts and quantities.
Refer to packing list for actual parts and quantities.
9 |
The information below is required for social login
Sign In
Create New Account